Vehicles
Sections
537 not categorized PORSCHE 356 A AC RODCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1989-94 (includes uncategorized and accessory items) TL1021 This universal flywheel lock has been designed for use on all air-cooled Porsche engines (series 356, 912, 914 & all 911s through 1969) and on all air-cooled volkswagen engines (type 1,2,3 & 4). This tool is a must when changing a flywheel or its seal and it comes in handy when changing a clutch. Made from a forging, this quality tool will last a lifetime. Gpcg91101000. General Fitment914 1970-76356 1950-59 356 1960-65 912 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69
$12.00
Make a selection 90142456703 Known as: push rod View/Change Diagram
From $48.76
Make a selection 90142429202 Not for spotomatic typ 925
From $13.80
Make a selection 64434732602B Es gibt 2 verschiedene versionen fur 356a und fur 356 b+c: der am konus zur verschraubung mit der kronenmutter sind unterschiedlich bei den beiden modellen - bis 1957 waren es am konus zur mutter 10,7mm -schmalste stelle-/12,2mm -breiteste stelle- - seit 1958 sind es 12,6mm/14,2mm.
$53.90
Make a selection 91120190400EQ Galvanized steel. (62l)
$512.60
Make a selection 64434732502B Es gibt 2 verschiedene versionen fur 356a und fur 356 b+c: der am konus zur verschraubung mit der kronenmutter sind unterschiedlich bei den beiden modellen - bis 1957 waren es am konus zur mutter 10,7mm -schmalste stelle-/12,2mm -breiteste stelle- - seit 1958 sind es 12,6mm/14,2mm.
$53.90
Make a selection
$62.76
Make a selection 13924 Universal 3-wire oxygen sensor. An inexpensive alternative to the more-expensive factory replacement o2 sensor. Note: requires you to remove the factory plug and wire this sensor in. General Fitment911 1987-89911 1989-94
$110.92
Make a selection 90110314181SET
$118.80
Make a selection 96410317600 View/Change Diagram
$14.55
Make a selection FVD424049ER If you are using numeric racing performance cables on your race car, then we suggest upgrading your rod ends to these steel ends which will take far more abuse at the track. These are recommended for race cars only as metal on metal contact means increased noise and vibration in the cabin. Sold individually.
$22.00
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$66.00
Make a selection FVD2857RSR21 Rsr / Bosch twin plug distributor reproduction. Custom made in Germany for use with 6 and 8 connectors , hkz elcetronic ignition.
$5,959.80
Make a selection FVD2857RSR21K Rsr / Bosch twin plug distributor reproduction. Custom made in Germany for use with 6 and 8 connectors , hkz elcetronic ignition.
$5,355.90
Make a selection
$871.77
Make a selection 10010303802 Perfect kit for street use, this is ultra-reliable, factory smooth kit will yield 35+ hp (depending on your additional modifications). These can also be used with OEM valves and camshafts. These are slip fit (107 spigot / 102 bore) and no modifications must be made to the case. Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have the piston rings (sealing and oil scrapers) pre-installed to ensure reliability. Each of our mahle piston and cylinder kits are complete and ready for installation. We also ...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $6,080.40
Make a selection FVDBRO107486580 This kit contains genuine brembo - ferodo fm 1000 street compound brake pads. Details: 130mm wide 18mm thick for use with b, h, p & 2 caliper (FVD part # FVD 351 1b…1h, etc) without the sensor cut out not for use with 380 x 32 mm discs
$341.00
Make a selection FVDBROXA571M2 Brake pad set for brembo kit FVD 351 1n.1m. With 380/355x32mm disc. With brake sensor cut-out.
$595.19
Make a selection 96434703200 If your outer tie rods are worn you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be very dangerous and can seriously affect steering control. Prevent that from happening by replacing them as quickly as possible with our genuine replacement inner tie rods. Once you do, you will experience tighter, more precise feedback without noise. Complete kit consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Ball joint end 1 qty. Lock nut & pin sold individually. Left or right side fitment. 2 qty. Required. Tech tip: replace the inner tie rods also for a new car steering feel ! Purchase our part # 96434705804 & 96434719...(choose a part on the right to read more) View/Change Diagram
From $55.29
Make a selection 10010303803 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. However, this kit cannot be used with original cams, it requires a more aggressive cam (maximum valve lift (tdc) of 2.1 mm) and has very deep pockets for use with rsr valves. The 109-mm size means that the housings / case must be modified / machined on non rs models. If you have a European rs model, these would be slip fit. This kit also requires 6 qty. Larger o-rings, part # 96410440180 and 6 qty. Larger base o-rings, part # 99970502341 mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high th...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $6,784.84
Make a selection 93010314781SET Oem parts, sourced directly from Germany. Sold individually. 1 necessary per car.
$366.30
Make a selection 91410314150SET High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 necessary per car.
$148.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |